Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Sun May 22, 2016 7:22 pm
Hell yes!
Looks awesome
Looks awesome
its getting there slowly!!!!!!
bought a new master cylinder and clutch fork grommet this arvo too.
Page 78 of 92
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Sun May 22, 2016 7:46 pm
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Sun May 22, 2016 9:23 pm
Glad to be of assistance.
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Sun May 22, 2016 9:59 pm
you were there for the booze!!!
Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Mon May 23, 2016 6:37 am
Man this things came along way since I last visited ya thread ,good work dude
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Luke's 1200 Coupe
Posted: Tue May 24, 2016 1:41 pm
Barts gonna Bart...
Posted: Thu May 26, 2016 10:05 am
Haha gold!
Sent from my SM-G920I using Tapatalk
Sent from my SM-G920I using Tapatalk
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Thu May 26, 2016 7:01 pm
Burn! 
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Fri Aug 19, 2016 1:18 pm
UPDATE!
got my newly refurbed starter motor and wiper motors picked up from rolly auto sparky thanks to hayden, getting them tomorrow.
won a cusco strut brace for $7k yen out of japan which is on its way here in a very slow boat.
grommets turned up for the engine bay courtesy of ebay.
zinced the hard lines for the brakes
redline datsun 1200 radiator turned up a while back but the holes to mount it are so far out compared to factory location its ridiculous.
small issue attaching the idler arm, due to the differing mounts i have for the engine it now fouls on the headers, unsure of brand but probably coby d1s or d2s. i read somewhere that one works but the other hits etc. unsure where to go with this issue for now. help please!
jeremy made me a sweet gbox xmember but i didnt give him quite enough measurements or offsets,the old xmember should never have been a template.
getting a plate made up to cover my fuel tank where the intank pump setup is.
got a small plastic clip so i can finally open the drivers door with the exterior handle, yet to fit it as i dont trust myself and dont wanna dissasemble a complete finished passenger side to see how it works. bribe brendan i think.
no point taking any pictures because it still looks the same at this stage sorry lads.
very seriously thinking about having a working bee on this if anyone was keen as at the rate im going this wont make nationals.
if anyone has a joiner clip for the gutter trim i will pay happily for one in good nick
got my newly refurbed starter motor and wiper motors picked up from rolly auto sparky thanks to hayden, getting them tomorrow.
won a cusco strut brace for $7k yen out of japan which is on its way here in a very slow boat.
grommets turned up for the engine bay courtesy of ebay.
zinced the hard lines for the brakes
redline datsun 1200 radiator turned up a while back but the holes to mount it are so far out compared to factory location its ridiculous.
small issue attaching the idler arm, due to the differing mounts i have for the engine it now fouls on the headers, unsure of brand but probably coby d1s or d2s. i read somewhere that one works but the other hits etc. unsure where to go with this issue for now. help please!
jeremy made me a sweet gbox xmember but i didnt give him quite enough measurements or offsets,the old xmember should never have been a template.
getting a plate made up to cover my fuel tank where the intank pump setup is.
got a small plastic clip so i can finally open the drivers door with the exterior handle, yet to fit it as i dont trust myself and dont wanna dissasemble a complete finished passenger side to see how it works. bribe brendan i think.
no point taking any pictures because it still looks the same at this stage sorry lads.
very seriously thinking about having a working bee on this if anyone was keen as at the rate im going this wont make nationals.
if anyone has a joiner clip for the gutter trim i will pay happily for one in good nick
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Posted: Fri Aug 19, 2016 2:59 pm
Prep that engine bay and Ill sort the wiring. And the door innards too.