i need a l18 or l20b.

sam910 · Post by **sam910** » Thu Dec 10, 2009 10:48 am

hole engine or just block . pm me if u have 1

2 doors · Post by **2 doors** » Thu Dec 10, 2009 9:52 pm

check the for sale section isnt matt selling an L18 with 5 speed?

sam910 · Post by **sam910** » Fri Dec 11, 2009 2:31 pm

yes and it is now sitting in my garage

soon to have my l20b fuel pump my peanut head and twin 40mm.... hpe its a good motor or it wont last long with me

Post by **Speed_Freak** » Fri Dec 11, 2009 10:31 pm

sam910 wrote:yes and it is now sitting in my garage soon to have my l20b fuel pump my peanut head and twin 40mm.... hpe its a good motor or it wont last long with me

That motor came out of whats his names 1600 SSS or something? I think its got a bigger oil pump or something? Cant remember!

sam910 · Post by **sam910** » Tue Dec 15, 2009 4:44 pm

well i put it in drv 2 wrk gt hme went to the shop and it started knking lyk a bitch AKA IT WAS A WASTE OF MONEY... spent my weekend putting it in

Post by **Speed_Freak** » Tue Dec 15, 2009 5:08 pm

Are you serious?? That motor was a minta ill hit him up at work man thats bullshit!

sam910 wrote:hpe its a good motor or it wont last long with me

Or did you rape the ass off it?

2 doors · Post by **2 doors** » Tue Dec 15, 2009 5:54 pm

id be checking the flywheel bolts, as its so common for them to come loose, especially if getting a caneing, sounds exactly like bottom end knock as well.

datman310 · Post by **datman310** » Tue Dec 15, 2009 5:59 pm

2 doors wrote:id be checking the flywheel bolts, as its so common for them to come loose, especially if getting a caneing, sounds exactly like bottom end knock as well.

happened to me once

sam910 · Post by **sam910** » Tue Dec 15, 2009 6:36 pm

mate i was nice as to it 7am going to cpit from linwood few to many cops for me to be rapin it .. was full off oil as well it had the l20b oil filter ..

flywheel??... mayb my l20b ran a bearing and wouldnt rev eg fukd

the l18 could still rev but i dnt see y it would be the flywheel the engine and box were still together

2 doors · Post by **2 doors** » Tue Dec 15, 2009 8:26 pm

seriously mate, the bolts can come loose, the flywheel will still be attatched to the crank as the bolts cant come all the way out, but it will knock like a bastard, if you were that nice to it and after a couple of trips it started knocking that bad, I wouldnt be putting my money on a fucked motor, otherwise it would have knocked from start-up, from what you are describing.
did the motor come with a flywheel? if so did you check the bolts? if not did you locktight the bolts when putting them in?

New Zealand Datsun Club

i need a l18 or l20b.

i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.

Re: i need a l18 or l20b.