NELSON MEMBERS and Z18et queries

[jasace]

Hi im new to this site.
Im building a airbaged d21 dbl cab navara & i hav just got a z18et for it.
So i was wondering if there are any nelson members that hav mucked round with z18et or know how to or can help me get it wired up so it runs in my navara?
Any help wood be good

Cheers JASACE

[Mikewazowski]

Hey mate, I'm not from Nelson (I'm up in the Bay of Plenty) but I've got a Z18ET wired up and running in my 610. Not sure how much assistance I can be but if you need any help just yell out.

[DylPhil7]

all of the GC's are down in christchurch bro haha i think theres like four guys including you and i from nelson in the 'club'
another nelson member!

[jasace]

Hey mate, I'm not from Nelson (I'm up in the Bay of Plenty) but I've got a Z18ET wired up and running in my 610. Not sure how much assistance I can be but if you need any help just yell out.

Sweet thank i think i get the wirein pixs of you the other nite?
I think once the motor is in & the loom is ran i jst have to work out what wires re the earth & acc & power for the ecu?
I know know if its as easy as that or not?
But im havnt touble founding a shop that can get me a hd cluth i been to 2 shops & they cant found any cluth for a z18et letalone a hd one

JASACE

[jasace]

all of the GC's are down in christchurch bro haha i think theres like four guys including you and i from nelson in the 'club'
another nelson member!

Thanks what are you building?

[Bartman]

Don't quote me cos I may be incorrect, (I'm sure someone will chime in if I am) but the Z series clutch may be interchangable with the L series ones. AFAIK they use the same block and crank as an L series. Hayden (brwnwgn) may know for sure as I know he had a Z block with an L head in a rally car.
There should be something available for an L series. Maybe try ringing Tony at clutch systems NZ limted in Hazeldean road in Christchurch? Hes a very helpful bloke to deal with. He should know about interchangabilty etc. Very good to deal with too.

[jasace]

Any pics of your engine bays with z18et in them wood b very helpful?

JASACE

[Bartman]

[DylPhil7]

all of the GC's are down in christchurch bro haha i think theres like four guys including you and i from nelson in the 'club'
another nelson member!

Thanks what are you building?

B310 bro, just replacing gearbox at the moment eh. need to cut and weld some rust out and lower it now lol
have you started a build thread yet???

[Mikewazowski]

Sweet thank i think i get the wirein pixs of you the other nite?
I think once the motor is in & the loom is ran i jst have to work out what wires re the earth & acc & power for the ecu?
I know know if its as easy as that or not?
But im havnt touble founding a shop that can get me a hd cluth i been to 2 shops & they cant found any cluth for a z18et letalone a hd one

JASACE

Yeah, datsunboy helped me wire my Z18ET up, and after seeing it done it isn't overly complicated. I ended up stripping the entire loom apart to try and find a few faults and it is pretty simple once you have it apart. I can take some photos of particular parts if you would like them explained. You pretty much wire some stuff up in the relay/battery area (power, earth, etc), and wire up a relay for your fuel pump, and you are away laughing.

I had trouble finding a clutch as well. It took a couple of goes getting one that fit as APPCO didn't list anything for Z18ET. Ended up getting it sent to a place in Auckland (can't remember the name just now) and sent down a new one which was perfect
I'll try and remember the name of the place it went to....