Braasy's Datsun 1200 (B110) 4 Door Sedan

Show everyone your mean datto projects/rides
z181200
Datsun Mad
Posts: 592
Joined: Sun Jul 20, 2008 10:46 am
Location: Christchurch

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by z181200 »

Roll your guards that helps heaps! They have a lip underneath them thats horizontal and pushing that flush with the guards gives you heaps of clearance.
braasmonkey
Site Admin
Posts: 994
Joined: Fri Dec 03, 2010 6:19 pm
aka: Braasy
Location: Sydney, Australia
Contact:

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by braasmonkey »

z181200 wrote:Roll your guards that helps heaps! They have a lip underneath them thats horizontal and pushing that flush with the guards gives you heaps of clearance.
I checked the clearance on full lock and it appears the tyres are rubbing against the firewall and not the guards. Will be trying to source a better jack tomorrow and some stands so I can have a proper look... Cheers for the heads up :)
1972 DATSUN 1200 (B110) 4 DOOR SEDAN << Check Out My Build Thread
1972 DATSUN 240Z (S30) 2 DOOR COUPE << Check Out My Build Thread
z181200
Datsun Mad
Posts: 592
Joined: Sun Jul 20, 2008 10:46 am
Location: Christchurch

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by z181200 »

What size the tyres and rims are they? Iv got 175 50 13s and the rub slightly on on the inner guard on one side. It doesnt really affect driving as the 1200s lock is so good you dont really need to full lock it very often. When it does rub its just a gentle rub not some savage tyre shredding so it doesnt concern me.
grant76
Datsun Nutter
Posts: 335
Joined: Sun Jul 20, 2008 7:09 pm
Location: matamata

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by grant76 »

185/55/14 is usually the biggest tyre you can use before guard mods become necessary (in my experience anyway)
braasmonkey
Site Admin
Posts: 994
Joined: Fri Dec 03, 2010 6:19 pm
aka: Braasy
Location: Sydney, Australia
Contact:

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by braasmonkey »

Kitch wrote:they are 185/55/14 tyres, mags are 14x6" with 15 offset
Cheers Kitch.
1972 DATSUN 1200 (B110) 4 DOOR SEDAN << Check Out My Build Thread
1972 DATSUN 240Z (S30) 2 DOOR COUPE << Check Out My Build Thread
braasmonkey
Site Admin
Posts: 994
Joined: Fri Dec 03, 2010 6:19 pm
aka: Braasy
Location: Sydney, Australia
Contact:

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by braasmonkey »

Wonder if some low profile tyres would make much of a difference with rubbing round corners and under weight/load?
Last edited by braasmonkey on Sat May 07, 2011 5:26 pm, edited 1 time in total.
1972 DATSUN 1200 (B110) 4 DOOR SEDAN << Check Out My Build Thread
1972 DATSUN 240Z (S30) 2 DOOR COUPE << Check Out My Build Thread
grant76
Datsun Nutter
Posts: 335
Joined: Sun Jul 20, 2008 7:09 pm
Location: matamata

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by grant76 »

you could try some 195/45/14 tyres on the front, they are a lower profile that should stop your rubbing problem hopefully?? they helped with a set of mags with a less than perfect offset fit ok on my ute
braasmonkey
Site Admin
Posts: 994
Joined: Fri Dec 03, 2010 6:19 pm
aka: Braasy
Location: Sydney, Australia
Contact:

Re: Braasy's Datsun 1200 (B110) 4 Door Sedan

Post by braasmonkey »

grant76 wrote:you could try some 195/45/14 tyres on the front, they are a lower profile that should stop your rubbing problem hopefully?? they helped with a set of mags with a less than perfect offset fit ok on my ute
Still have issues in the back so will need a set methinks. Might check out the tyre/wheel warehouses around town for pricing etc on a set and go from there. In the meantime and to get a warrant, may stick the 12" SSS wheels back on and repair the one that is flat. Cheers for the input.
1972 DATSUN 1200 (B110) 4 DOOR SEDAN << Check Out My Build Thread
1972 DATSUN 240Z (S30) 2 DOOR COUPE << Check Out My Build Thread
Post Reply