CRAIGS 510 1600
-
DylPhil7
- Financial Member
- Posts: 1113
- Joined: Fri Jun 19, 2009 8:33 pm
- aka: DylPhil
- Location: Wellington
- Contact:
Re: CRAIGS 510 1600
nice man, how much power you hoping to get out of it?
-
Msdato
- Financial Member
- Posts: 230
- Joined: Sun Aug 02, 2009 3:13 pm
- aka: Jo
- Location: Chch
- Location: Christchurch
- Contact:
Re: CRAIGS 510 1600
You should most def come down in Oct for labour weekend, show off some datto talent, Looks sweet man
[MSDATO] B110 74 Sedan.
[EPW627] pfl S14. My other better-behaved child.
[EPW627] pfl S14. My other better-behaved child.
-
Bartman
- Committee Members
- Posts: 7303
- Joined: Sat Jul 19, 2008 9:04 am
- Location: Datsun City
- Location: Christchurch New Zealand!!!!
- Contact:
Re: CRAIGS 510 1600
You can do it Craig.
I reckon the word can't means can't be fucked!
I reckon the word can't means can't be fucked!
They don't call me the man with the rubber arm for nothing you know.............
-
Brnwgn
- Financial Member
- Posts: 836
- Joined: Mon Aug 11, 2008 5:53 pm
- aka: Hayden
- Location: Oamaru
- Contact:
Re: CRAIGS 510 1600
do it do it!!
-
hsepwr
- Datsun Nutter
- Posts: 428
- Joined: Mon Sep 22, 2008 9:18 pm
- aka: Craig
- Location: Hastings
- Contact:
Re: CRAIGS 510 1600
haha id love too but i still got a lot of work on it especially now that it has the 4 pots on the front and disks on the rear i am up for a cert now as I need a wof and ive got alot to do engine exhaust , New brake lines etc
Next year might be a goer
Next year might be a goer
I REAKON THE WORD CANT MEANS CANT BE FU%&#CKED
-
Bartman
- Committee Members
- Posts: 7303
- Joined: Sat Jul 19, 2008 9:04 am
- Location: Datsun City
- Location: Christchurch New Zealand!!!!
- Contact:
Re: CRAIGS 510 1600
You can do it Craig. My car has no engine, is on blocks, and has structural rust, and I plan to bring it on the cruise. Just find a dodgey wof guy. I know one guy in the bay who might be sympathetic to your cause.
They don't call me the man with the rubber arm for nothing you know.............
-
510BRE
- Area Reps
- Posts: 899
- Joined: Mon Sep 08, 2008 9:46 pm
- aka: shane
- Location: hastings
- Location: hastings
Re: CRAIGS 510 1600
hey craig i got a spear seat to akaroa am leaving early thursday and back about tuesday
1972 r/h drive 2dr P510 sedan 98 sr20det in the build
1969 l/h drive 2dr PL510 sedan bre look alike
1972 r/h drive 4dr P510 sedan pretty standard
1969 l/h drive 2dr PL510 sedan bre look alike
1972 r/h drive 4dr P510 sedan pretty standard
-
hsepwr
- Datsun Nutter
- Posts: 428
- Joined: Mon Sep 22, 2008 9:18 pm
- aka: Craig
- Location: Hastings
- Contact:
Re: CRAIGS 510 1600
Latest update
I have been very slack and have all of a sudden given myself a kick up the arse to get my car back together.I had an operation on my arm in June and was in cast 3 months and was unable to work on car but I have been out of it for 3 months and still was being slack so its time to get back into it.
I sent the motor to a Very good engine builder in Hawkesbay here and he got the block and head and CC'd it and skimmed a bit off the block to raise compression, acid dipped everything, machined and balanced the crank, machined the bores, measured everything and lightened the flywheel a little bit more and I have since got it back and painted the block and matched ported the extractors to the head because they are shit Coby ones and were so far out it was not funny.The cam is going to franklins in the next week or so for what they call a stage 6 grind which means bugger all to me as im a joiner not a mechanic and dont understand cams at all. I am ordering the rings, bearings, oil and water pump and gasket set in the next week or two and then throwing it back together.
I have been very slack and have all of a sudden given myself a kick up the arse to get my car back together.I had an operation on my arm in June and was in cast 3 months and was unable to work on car but I have been out of it for 3 months and still was being slack so its time to get back into it.
I sent the motor to a Very good engine builder in Hawkesbay here and he got the block and head and CC'd it and skimmed a bit off the block to raise compression, acid dipped everything, machined and balanced the crank, machined the bores, measured everything and lightened the flywheel a little bit more and I have since got it back and painted the block and matched ported the extractors to the head because they are shit Coby ones and were so far out it was not funny.The cam is going to franklins in the next week or so for what they call a stage 6 grind which means bugger all to me as im a joiner not a mechanic and dont understand cams at all. I am ordering the rings, bearings, oil and water pump and gasket set in the next week or two and then throwing it back together.
I REAKON THE WORD CANT MEANS CANT BE FU%&#CKED
-
Bartman
- Committee Members
- Posts: 7303
- Joined: Sat Jul 19, 2008 9:04 am
- Location: Datsun City
- Location: Christchurch New Zealand!!!!
- Contact:
Re: CRAIGS 510 1600
Yeah those coby headers aint flash on the port matching front. It doesn't help when the ports in the head have been worked also.
BTW, it's less than 12 months untill the akoroa cruise. You need to start saving/making plans now! That cruise is unmissable.
BTW, it's less than 12 months untill the akoroa cruise. You need to start saving/making plans now! That cruise is unmissable.
They don't call me the man with the rubber arm for nothing you know.............
-
hsepwr
- Datsun Nutter
- Posts: 428
- Joined: Mon Sep 22, 2008 9:18 pm
- aka: Craig
- Location: Hastings
- Contact:
Re: CRAIGS 510 1600
Yeh thats true but the flanges on the extractors needed about 5mm the whole way round.It must have been like trying to piss through a straw when they used to be on it
I REAKON THE WORD CANT MEANS CANT BE FU%&#CKED