Hell yes!
Looks awesome
Luke's 1200 Coupe
-
Tony_Whenua
- Financial Member
- Posts: 433
- Joined: Fri Jan 13, 2012 6:58 pm
- Location: Blenheim
- Contact:
Re: Luke's 1200 Coupe NOW WITH ENGINE!
"Dude you're like 30 degrees retarded" - Chris_g1 & 2 Doors
Re: Luke's 1200 Coupe NOW WITH ENGINE!
its getting there slowly!!!!!!
bought a new master cylinder and clutch fork grommet this arvo too.
bought a new master cylinder and clutch fork grommet this arvo too.
1972 1200 coupe KB110
-
Bartman
- Committee Members
- Posts: 7303
- Joined: Sat Jul 19, 2008 9:04 am
- Location: Datsun City
- Location: Christchurch New Zealand!!!!
- Contact:
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Glad to be of assistance.
They don't call me the man with the rubber arm for nothing you know.............
-
kobyn
- Datsun Mad
- Posts: 638
- Joined: Fri Jul 15, 2011 8:44 pm
- Location: feilding manawatu
- Location: colyton
- Contact:
Luke's 1200 Coupe NOW WITH ENGINE!
Man this things came along way since I last visited ya thread ,good work dude
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Luke's 1200 Coupe
Barts gonna Bart...
You do not have the required permissions to view the files attached to this post.
-
datsunboy
- Datsun God
- Posts: 2016
- Joined: Fri Jul 18, 2008 10:31 pm
- aka: Dan
- Location: Christchurch
- Contact:
Haha gold!
Sent from my SM-G920I using Tapatalk
Sent from my SM-G920I using Tapatalk
1969 SSS Nissan Bluebird coupe
1970 Datsun 1600 - CA18DET - Sold!
1970 Datsun 1600 - CA18DET - Sold!
-
Bartman
- Committee Members
- Posts: 7303
- Joined: Sat Jul 19, 2008 9:04 am
- Location: Datsun City
- Location: Christchurch New Zealand!!!!
- Contact:
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Burn! 
They don't call me the man with the rubber arm for nothing you know.............
Re: Luke's 1200 Coupe NOW WITH ENGINE!
UPDATE!
got my newly refurbed starter motor and wiper motors picked up from rolly auto sparky thanks to hayden, getting them tomorrow.
won a cusco strut brace for $7k yen out of japan which is on its way here in a very slow boat.
grommets turned up for the engine bay courtesy of ebay.
zinced the hard lines for the brakes
redline datsun 1200 radiator turned up a while back but the holes to mount it are so far out compared to factory location its ridiculous.
small issue attaching the idler arm, due to the differing mounts i have for the engine it now fouls on the headers, unsure of brand but probably coby d1s or d2s. i read somewhere that one works but the other hits etc. unsure where to go with this issue for now. help please!
jeremy made me a sweet gbox xmember but i didnt give him quite enough measurements or offsets,the old xmember should never have been a template.
getting a plate made up to cover my fuel tank where the intank pump setup is.
got a small plastic clip so i can finally open the drivers door with the exterior handle, yet to fit it as i dont trust myself and dont wanna dissasemble a complete finished passenger side to see how it works. bribe brendan i think.
no point taking any pictures because it still looks the same at this stage sorry lads.
very seriously thinking about having a working bee on this if anyone was keen as at the rate im going this wont make nationals.
if anyone has a joiner clip for the gutter trim i will pay happily for one in good nick
got my newly refurbed starter motor and wiper motors picked up from rolly auto sparky thanks to hayden, getting them tomorrow.
won a cusco strut brace for $7k yen out of japan which is on its way here in a very slow boat.
grommets turned up for the engine bay courtesy of ebay.
zinced the hard lines for the brakes
redline datsun 1200 radiator turned up a while back but the holes to mount it are so far out compared to factory location its ridiculous.
small issue attaching the idler arm, due to the differing mounts i have for the engine it now fouls on the headers, unsure of brand but probably coby d1s or d2s. i read somewhere that one works but the other hits etc. unsure where to go with this issue for now. help please!
jeremy made me a sweet gbox xmember but i didnt give him quite enough measurements or offsets,the old xmember should never have been a template.
getting a plate made up to cover my fuel tank where the intank pump setup is.
got a small plastic clip so i can finally open the drivers door with the exterior handle, yet to fit it as i dont trust myself and dont wanna dissasemble a complete finished passenger side to see how it works. bribe brendan i think.
no point taking any pictures because it still looks the same at this stage sorry lads.
very seriously thinking about having a working bee on this if anyone was keen as at the rate im going this wont make nationals.
if anyone has a joiner clip for the gutter trim i will pay happily for one in good nick
1972 1200 coupe KB110
-
mint16
- Financial Member
- Posts: 1854
- Joined: Sat Jul 19, 2008 8:36 am
- aka: Brendan
- Location: Christchurch
Re: Luke's 1200 Coupe NOW WITH ENGINE!
Prep that engine bay and Ill sort the wiring. And the door innards too.
72 Datsun 1200 Wagon
86 Toyota AE85 Trueno 4AGE ITB
86 Toyota AE85 Trueno 4AGE ITB