Find me some Ca16 cams and I'll use them! Ca18 ex cam on the inlet side need adjustable cam gears to get timing perfect so I have read on the interwebs anyway
Sent from my GT-I9300 using Tapatalk 2
Datto_610's 180B - Street Legal!
-
Datto_610
- Datsun God
- Posts: 2976
- Joined: Sun Jul 20, 2008 10:39 am
- aka: Greg
- Location: Christchurch, NZ
- Location: Christchurch, NZ
- Contact:
Re: Datto_610's 180B Off with its head!
Right! Head gasket, tensioners and cam belt acquired. Appco didn't have any head bolts and Nissan couldn't get any til monday but BNT by my work are getting some in overnight. Sunday is going to be a busy day!
Re: Datto_610's 180B Off with its head!
"It's ok, we know what to do...we talked about this a lot on the internet."
-
Datto_610
- Datsun God
- Posts: 2976
- Joined: Sun Jul 20, 2008 10:39 am
- aka: Greg
- Location: Christchurch, NZ
- Location: Christchurch, NZ
- Contact:
Re: Datto_610's 180B Off with its head!
Yeah not cheap........
-
85_Z31
- Datsun Master
- Posts: 1494
- Joined: Sun Jul 18, 2010 10:53 pm
- Location: Rangiora North Canterbury
Re: Datto_610's 180B Off with its head!
have that service manual ready Greg.
A printed copy of the pages you need would be ideal.
Bring a bunch of Scrapers,scotch bright, brake cleaner and like an old sheet or something. You wont just be banging into it either, prep is key for Cylinder head installs
A printed copy of the pages you need would be ideal.
Bring a bunch of Scrapers,scotch bright, brake cleaner and like an old sheet or something. You wont just be banging into it either, prep is key for Cylinder head installs
The Answer to your Question is NEEDS MORE VG30
-
Datto_610
- Datsun God
- Posts: 2976
- Joined: Sun Jul 20, 2008 10:39 am
- aka: Greg
- Location: Christchurch, NZ
- Location: Christchurch, NZ
- Contact:
Re: Datto_610's 180B Off with its head!
Alrightey chief!
Sent from my GT-I9300 using Tapatalk 2
Sent from my GT-I9300 using Tapatalk 2
-
Datto_610
- Datsun God
- Posts: 2976
- Joined: Sun Jul 20, 2008 10:39 am
- aka: Greg
- Location: Christchurch, NZ
- Location: Christchurch, NZ
- Contact:
Re: Datto_610's 180B Off with its head!
Just got a call from BNT head studs didn't make the overnight courier 
But that's ok James has informed me there is still a lot of prep work to do and should have them on monday.
But that's ok James has informed me there is still a lot of prep work to do and should have them on monday.-
Datto_610
- Datsun God
- Posts: 2976
- Joined: Sun Jul 20, 2008 10:39 am
- aka: Greg
- Location: Christchurch, NZ
- Location: Christchurch, NZ
- Contact:
Re: Datto_610's 180B Off with its head!
Got the block all prepped ready for head installation next weekend. Gave #4 piston a smoothing over so no rough spots now will hopefully be ok 
Unbolted water pump just to have a nosey and shit there was a lot of gunk in there! Looks like it might be the original pump 
got all the crap out of the block and will get a new one this week. All going well head will be back on next Sunday yay.
Sent from my GT-I9300 using Tapatalk 2
Unbolted water pump just to have a nosey and shit there was a lot of gunk in there! Looks like it might be the original pump got all the crap out of the block and will get a new one this week. All going well head will be back on next Sunday yay.Sent from my GT-I9300 using Tapatalk 2
You do not have the required permissions to view the files attached to this post.
-
Godzilladat
- Datsun Nutter
- Posts: 406
- Joined: Sat Jul 19, 2008 7:57 pm
- Location: Australia
Re: Datto_610's 180B Off with its head!
Good to see you are progressing dude, even after some bad luck with the motor side of things
Re: Datto_610's 180B Off with its head!
oh well, at least you will have piece of mind on the cooling system side of things, next week should be exciting